Network Manage Tech Experience

Welcome to my tech home !!!
posts - 32, comments - 35, trackbacks - 0, articles - 0
  IT博客 :: 首页 :: 新随笔 :: 联系 :: 聚合  :: 管理

交换机通过port-channel互联

Posted on 2008-03-19 23:12 chris_lee 阅读(4410) 评论(0)  编辑 收藏 引用 所属分类: CISCO技术篇

对线上交换机进行配置修改,出现交换机暂时断网.原有情况:
  2台交换机通过2对光纤连接,分别作上port-channel,并将交换机的相应端口绑定在po上,启用trunk模式.交换机上原有几个vlan,但是在这个Po上只允许vlan21通过.如:
  上联交换机A部分配置:
  interface Port-channel1
   switchport trunk encapsulation dot1q
   switchport trunk allowed vlan 21
   switchport mode trunk
   !
  interface GigabitEthernet1/0/3
   description to-YH06050001_g1/0/25
   switchport trunk encapsulation dot1q
   switchport trunk allowed vlan 21
   switchport mode trunk
   channel-group 1 mode on
  !
  interface GigabitEthernet1/0/4
   description to-YH06050001_g1/0/26
   switchport trunk encapsulation dot1q
   switchport trunk allowed vlan 21
   switchport mode trunk
   channel-group 1 mode on
  !
  下联交换机B部分配置:
  interface Port-channel1
   switchport trunk encapsulation dot1q
   switchport trunk allowed vlan 21
   switchport mode trunk
  !
  interface GigabitEthernet1/0/25
   description to-CN_3523_g1/0/3
   switchport trunk encapsulation dot1q
   switchport trunk allowed vlan 21
   switchport mode trunk
   udld port
   channel-group 1 mode on
  !
  interface GigabitEthernet1/0/26
   description to-CN_3523_g1/0/4
   switchport trunk encapsulation dot1q
   switchport trunk allowed vlan 21
   switchport mode trunk
   channel-group 1 mode on
  !
  现在在这2个交换机上分别新建一个vlan254,并且需要在它们之间互通vlan254.于是在分别建立vlan254后,在A上作如下配置:
  int port-channel 1
   switchport trunk allow vlan add 254
  int range g1/0/3 -4
   switchport trunk allow vlan add 254
  然后在交换机B上作如下配置:
  int range g1/0/25 -26
   switchport trunk allow vlan add 254
  此时出现交换机B立即断网,于是马上进机房察看交换机这2个端口的状态灯发现显示沉黄色.console登陆,删除这一配置,端口才up.查看log发现:vlan mask is not matching.因为po上还没有进行配置.然后进行如下配置:
  int port-channel 1
   switchport trunk allow vlan add 254
  此时sh run,发现
  int range g1/0/25 -26
   switchport trunk allow vlan add 254
  这2个端口竟然自动配置上了vlan254.
  于是另外再做实验,对于没有做po的端口,可以直接加类似 switchport trunk allow vlan add 254 这样的配置.

经验总结:
  对trunk链路进行添加vlan配置时:
  1,对于物理trunk端口绑定在逻辑端口port-channel的情况,需要先对逻辑端口进行配置,这样的配置可以自动配置到物理链路上.(扩充:是否所有对于物理链路的配置都可以先在逻辑链路上配置,且自动配置在相应的物理链路上呢?)
  2,对于直接物理链路(没有绑定在逻辑链路上)的情况,可以直接对物理链路进行 switchport trunk allow vlan add 254 类似配置.

只有注册用户登录后才能发表评论。